Highly active photocatalytic coatings prepared by a low-temperature method

Photocatalytic properties of titanium (IV) oxide (TiO₂) in anatase form can be used for various purposes, including photocatalytic purification of water. For such an application, suspended or fixed photocatalytic reactors are used. Those with fixed phase seem to be preferred due to some advantages, one of which is the avoidance of photocatalyst filtration. To avoid leaching and exfoliation of the fixed phase, an immobilization procedure leading to a good adhesion of a catalyst to a substrate is crucial. Within this work, we present physical and photocatalytic characterization results of five commercially available TiO₂ photocatalysts (P25, P90, PC500, KRONOClean 7000, VPC-10) and one pigment (Hombitan LO-CR-S-M), which were successfully immobilized on glass slides by a “sol suspension” procedure. Different mechanical tests and characterization methods were used to evaluate the stability and morphology of the layers. Evaluation of photocatalytic activity was done by tests under UVA and UV–vis irradiation, using a method based on the detection of the fluorescent oxidation product of terephthalic acid (TPA), i.e., hydroxyterephthalic acid (HTPA). Aeroxide® P90 incorporated into the silica-titania binder was the most photocatalytically active layer and, unlike the others, showed significant increase of photocatalytic activity through the entire range of tested UVA irradiation intensities (2.3 mW/cm²–6.1 mW/cm²). The high mechanical stability of some photocatalytic layers allows using them in water photocatalytic purification reactions.     

Impact of industrial pollution on Scots pine (Pinus sylvestris L.) radial growth in the areas of mineral fertilizer factory “Achema”

The aim of research was to assess the changes of annual radial increment of Scots pine forests in the vicinity of intensive and moderate industrial pollution of “Achema” factory producing mineral fertilizers. Our results indicate that the radial growth of the pine tree can be divided into three different periods: growth promotion, growth inhibition and growth recovery. Low levels of nitrogen emissions were beneficial for tree growth: the radial increment in the intensive and moderate pollution zones increased by 15–25% and 10%, respectively compared to control. During the growth inhibition period, the total annual industrial emission was 37–40 kt, and 40–45% radial growth loss was observed for the closest and 15–20% for the most distant stands. The radial growth decrease slowed down and the recovery of damaged stands began in 1990–1992 then air pollution was considerably reduced. The rate of forest recovery was high for the most damaged stands: their radial growth was close to control in 2000–2011.     

Characterisation of secondary metal-bearing phases in used dental amalgam and assessment of gastric solubility

Detailed SEM/EDS investigation of used dental amalgams was carried out in order to characterise morphology and chemical composition of secondary metal-bearing phases resulting from long-term exposure of dental amalgam to oral environment, and assess their solubility in gastric environment. The investigation revealed numerous secondary phases, represented by compositionally and morphologically complex Hg-, Cu-, Sn-, Ag-, Zn-bearing sulphides and oxides/hydroxides, while sulphates and phosphates are scarce. Secondary metal-bearing phases mostly occur at the amalgam/tooth interface; however, some phases were found only on the occlusal surfaces of amalgam. Secondary phases mostly form porous aggregates of minute crystallites and micro- or nanocrystalline crusts. In oral environment, these phases are mostly stable and represent trapping media for dissolved potentially toxic metals released during amalgam corrosion. Simplified PHREEQC calculations of solubility of secondary metal-bearing phases in aqueous environment under conditions similar to those in gastric environment showed that secondary phases are more soluble in gastric environment than in oral solutions, which is mostly due to their forms of occurrence. Secondary phases in gastric environment thus act as secondary sources of potentially toxic metals, particularly Sn, Zn and also Cu, which are released both under reducing and oxidising conditions especially in acidic environment. Only very small amounts of Hg are potentially released and should not represent serious threat. Secondary phases that contribute the most to bioaccessibility of these metals are Sn hydroxychlorides, Sn oxides/hydroxides, Sn sulphates/hydroxysulphates, Sn oxides, Zn sulphides and Cu sulphides (Cu₂S).

     

The reproduction of Enchytraeus sp.—technical improvement for the counting of juveniles

Soil-dwelling annelids of the genus Enchytraeus are used in ecotoxicology for testing of chemicals mixed in artificial soil or for testing of wastes and soils of unknown quality. ISO 16387 describes a method for determining the effects of substances or contaminated soils on survival and reproduction of Enchytraeus albidus or of the smaller species Enchytraeus buchholzi or Enchy-traeus crypticus. After the total test duration of 6 (or 4)?weeks, the juveniles hatched in the meantime are counted. There are several possible extraction techniques, which are always followed by counting the juveniles by hand, but none of them seems easy to handle. We proposed a new modification of the worm extraction method using flotation of fixed and stained juveniles followed by taking a photograph. The digital image of the juveniles is evaluated by computer processing. It makes the counting of juveniles much easier and less labor intensive.     

Effect of ferrate on green algae removal

Green algae Cladophora aegagropila, present in cooling water of thermal power plants, causes many problems and complications, especially during summer. However, algae and its metabolites are rarely eliminated by common removal methods. In this work, the elimination efficiency of electrochemically prepared potassium ferrate(VI) on algae from cooling water was investigated. The influence of experimental parameters, such as Fe(VI) dosage, application time, pH of the system, temperature and hydrodynamics of the solution on removal efficiency, was optimized. This study demonstrates that algae C. aegagropila can be effectively removed from cooling water by ferrate. Application of ferrate(VI) at the optimized dosage and under the suitable conditions (temperature, pH) leads to 100% removal of green algae Cladophora from the system. Environmentally friendly reduction products (Fe(III)) and coagulation properties favour the application of ferrate for the treatment of water contaminated with studied microorganisms compared to other methods such as chlorination and use of permanganate, where harmful products are produced.

     

Plant species richness of riverbed elevations—the Pripyat river valley case study

Flora of the still unchanged or slightly modified floodplains is particularly valuable. Such are the natural, periodically flooded riparian ecosystems within the Mid-Pripyat river valley in Belarus. Distinctive elements of that area are ‘periodic islands’, which arise from the most elevated parts of the riverbed during flooding and have a specific microtopography. The aim of the research was to recognize floristic composition and ecological conditions of the ‘islands.’ Noted plants were mainly photophilous, by clearly varied in soil moisture, acidity and fertility requirements.     

Carbonyl emissions from vehicular exhausts sources in Hong Kong

Vehicular emission (VE) is one of the important anthropogenic sources for airborne carbonyls in urban area. Six types of VE-dominated samples were collected at representative locations in Hong Kong where polluted by a particular fueled type of vehicles, including (i) a gas refilling taxis station (liquefied petroleum gas [LPG] emission); (ii) a light-duty passenger car park (gasoline emission); (iii) a minibus station (diesel emission); (iv) a single-deck-bus depot (diesel emission); (v) a double-deck-bus depot (diesel emission); and (vi) a whole-food market entrance for light- and heavy-duty vehicles (diesel emission). A total of 15 carbonyls in the samples were quantified. Formaldehyde was the most abundant carbonyl among the VE-dominated samples, and its contribution to the total quantified amount on a molar basis ranged from 54.8% to 60.8%. Acetaldehyde and acetone were the next two abundant carbonyls. The carbonyls were quantified at three roadside locations in Hong Kong. The highest concentrations of formaldehyde and acetaldehyde, 22.7 +/- 8.4 and 6.0 +/- 2.8 microg/m3, respectively, were determined in the samples collected at a main transportation gate for goods between Hong Kong and Mainland China. The total quantified carbonyl concentration, 37.9 +/- 9.3 microg/m3, was the highest at an entrance of a cross-harbor tunnel in downtown area. The theoretical carbonyls compositions of the three roadside locations were estimated according to the VE-dominated sample profiles and the statistics on vehicle numbers and types during the sampling period. The measured compositions of formaldehyde were much higher than the theoretical compositions in summer, demonstrating that photochemical reactions significantly contributed to the formaldehyde production in the roadsides.     

The Properties of Poly(<Emphasis Type="SmallCaps">l</Emphasis>-Lactide) Prepared by Different Synthesis Procedure

Different synthesis methods were applied to determine optimal conditions for polymerization of (3S)-cis-3,6-dimethyl-1,4-dioxane-2,5-dione (l-lactide), in order to obtain poly(l-lactide) (PLLA). Bulk polymerizations (in vacuum sealed vessel, high pressure reactor and in microwave field) were performed with tin(II) 2-ethylhexanoate as the initiator. Synthesis in the vacuum sealed vessel was carried out at the temperature of 150 °C. To reduce the reaction time second polymerization process was carried out in the high pressure reactor at 100 °C and at the pressure of 138 kPa. The third type of rapid synthesis was done in the microwave reactor at 100 °C, using frequency of 2.45 GHz and power of 150 W at the temperature of 100 °C. The temperature in this method was controlled via infrared system for in-bulk measuring. The solution polymerization (with trifluoromethanesulfonic acid as initiator) was possible even at the temperature of 40 °C, yielding PLLA with narrow molecular weight distribution in a very short period of time (less than 6 h). The obtained polymers had the number-average molecular weights ranging from 43,000 to 178,000 g mol⁻¹ (polydispersity index ranging from 1 to 3) according to the gel permeation chromatography measurements. The polymer structure was characterized by Fourier transform infrared and NMR spectroscopy. Thermal properties of the obtained polymers were investigated using thermogravimetry and differential scanning calorimetry.